• MSP-EXP430G2 LaunchPad Evaluation Kit User's Guide Literature Number: SLAU318F July 2010 – Revised January 2015. • Getting Started With MSP-EXP430G2 LaunchPad Hp Pre Installed Programs In Registry. ...Getting Started..Demo Application, Internal Temperature Measurement.. Develop an Application With the MSP-EXP430G2 LaunchPad...Developing an Application. Program and Debug the Temperature Measurement Demo Application..Disconnect Emulator From Target With Jumper J3..
• Code Composer Studio™ v4 in Debugging Mode Hp Dl380 G7 Nic Drivers more. .MSP-EXP430G2 LaunchPad With Attached eZ430-RF2500 Target Board... Device Pinout..Schematics, MSP-EXP430G2 Emulator (1 of 2), Revision 1.4..Schematics, MSP-EXP430G2 Emulator (2 of 2), Revision 1.4..Schematics, MSP-EXP430G2 Target Socket, Revision 1.4.. • Preface: Read This First If You Need Assistance If you have any feedback or questions, support for the MSP430™ devices and the MSP-EXP430G2 is provided by the Texas Instruments Product Information Center (PIC) and the TI E2E Forum (Contact information for the PIC can be found on the TI web site at • • High-quality 20-pin DIP socket for an easy plug-in or removal of the target device Figure 1. MSP-EXP430G2 LaunchPad Overview Kit Contents The MSP-EXP430G2 evaluation kit includes the following hardware: • LaunchPad emulator socket board (MSP-EXP430G2) • Mini USB-B cable, 0.5 m •. • MSP430G2xx based application on the LaunchPad.
Install the Hardware Connect the MSP-EXP430G2 LaunchPad socket board with the enclosed USB cable to a PC. The driver installation starts automatically. If prompted for software, allow Windows to install the software automatically.
Cronica De Familie Petru Dumitriu Pdf Printer. • Getting Started With MSP-EXP430G2 LaunchPad Getting Started The first time the MSP-EXP430G2 LaunchPad Evaluation Kit is used, a demo application automatically starts as soon as the board is powered from the USB host. To start the demo, connect the MSP- EXP430G2 LaunchPad with the included mini USB cable to a free USB port. • Section 2 offer support for the whole MSP430G2xx Value Line. The MSP-EXP430G2 LaunchPad needs only a connection to the USB of the Host PC—there is no external hardware required. The power supply and the Spy-Bi-Wire JTAG signals TEST and RST must be connected with jumper J3 to allow the onboard emulation connection to the device.
The Launchpad does what it does quite well. E-mu could have put a lot more effort into the 'drum pads' - they *really* suck. And it should be cheaper. Other than that, it's a great niche product. (Thanks to Sam Bretheim for this info.) Links for the Emu Launchpad.
• VCC must be opened, and a multi meter can used on the VCC Jumper to measure the current of the MSP-EXP430G2 target device and its peripherals. The jumper J5 VCC also must be opened if the LaunchPad board is powered with an external power supply over J6 Table 1 or the eZ430 interface J4. • TEST and RST of J3 must be open. The interface to the eZ430 target board is always connected to the MSP-EXP430G2 emulator, so the programming and debugging of a connected LaunchPad target device is possible only if the eZ430 target is not connected on the same time. The application UART, on the other hand, is connected directly to the LaunchPad target device, and jumper J3 can be closed to monitor the transmission from the LaunchPad target to the attached eZ430. • Connecting a Crystal Oscillator The MSP-EXP430G2 LaunchPad offers a footprint for a variety of crystal oscillators. Hp Windows Xp Pro Sp2 Product Key. The XIN and XOUT signals of the LFXT1 oscillator can support low-frequency oscillators like a watch crystals of 32768 Hz or a standard crystal with a range defined in the associated data sheet.